| Author | Message | ||
     Subzero Comedian Username: Subzero Post Number: 1799 Registered: 04-2008 Posted From: 59.93.89.84 Rating: |
this is not required. I voted without that slip. Voter id card itself is enough. EVMs lo emi kiri kiri ledu. Just my opinion. సర్వ దేవాత్మకో హ్యేస తేజస్వీ రశ్మీభావనాః ఎస దేవాసుర గణమ్ లోకాం పాతి గభాస్తీభీః | ||
| Arjun1234 Junior Artist Username: Arjun1234 Post Number: 359 Registered: 09-2008 Posted From: 24.5.244.196 Rating: N/A |
EVMs pai apohalela ... IV subba Rao http://www.andhrajyothy.com/latestmainshow.asp?qry=/2009/may /30new66 cast your vote here: www.andhrasuperstar.com | ||
| Arjun1234 Junior Artist Username: Arjun1234 Post Number: 358 Registered: 09-2008 Posted From: 24.5.244.196 Rating: N/A |
yup my strong doubts on RJY as well... cast your vote here: www.andhrasuperstar.com | ||
| Arjun1234 Junior Artist Username: Arjun1234 Post Number: 357 Registered: 09-2008 Posted From: 24.5.244.196 Rating: N/A |
EVMs pai anta ulku enduku - TDP http://eenadu.net/advancepanelhtml.asp?qrystr=htm/panel6a.ht m cast your vote here: www.andhrasuperstar.com | ||
| Arjun1234 Junior Artist Username: Arjun1234 Post Number: 356 Registered: 09-2008 Posted From: 24.5.244.196 Rating: N/A |
How the EVMs Could have been manipulated through remote control: To discuss this possible scenario, We need to assume that the wireless transmitter/emitter had been embedded in right at the manufacturing of the Chip itself. (Note: THe chip manufacturing happens at a different place, well before EVM production) There is a unique ID assigned to each EVM, and each of the EVM could be contacted separately, using this unique ID. Can such a wireless component be detected or traced? * The wireless componenet in a chip, cannot be detected, unless, it transmits or emits signals. The Chip might have been programmed to transmit data only upon receiving certain command through specific frequency. In this case, the receiver component might be in listen mode, waiting for a particular command, known only to a core expert group. So, in a normal circumstance, this wireless component will be in hidden mode. Can the architecture of the CHIP be verified? * To my knowledge, a chipâs internal circuitry cannot be verified after it is manufactured. In our case, the expert committee had verified only the approved architecture for use in production. However, it doesnt gaurantee, that all the Chips manufactured there are as per the original design. * The current architecture might have been obtained by the hackers, and additional wireless component introduced, and this new modified architecture might be produced at some different place and then used during the assembly of EVMs. * The size, apperance, and even the Unique ID of the Chip would be emulated as it is, and thus it is extremely difficult to verify, if the current Chip components used is indeed the original one. The EVMs are all despatched to the respective constituencies, and the high level âRigging / hacking teamâ, will ensure that the EVMâs with wireless component is delievered to the appropriate constituency. Now, the election would be conducted regularly, and the EVMs are stored in a highly secured location in each constituency. Now, the core hacking team comes in to picture. We know that there are two days b/w last phase of voting and counting. In that time interval, the following is possible. * Using specially designed device, the core hacking team, can connect to each of the EVMâs through satellite connection, and obtain the voting data in to its computer. This is possible, since each EVM has a unique ID, and using that ID, they can connect to each and every EVM accurately. * All the data would be downloaded to a computer, according to EVMâs. * Now, in the selected constituencies, the votes are adjusted in each EVMâs used there, to increase the tally of the ruling party. Suppose, if there are 1500 boths in a constituency, and each booth having 1000 voters, with an average voting of 750 votes. If we could adjust, atleast 50 votes in each booth, it comes around 45,000 votes in all the 1500 booths. And this 50 votes need not be taken from any single party. For example, in a particular constituency, 20 votes from ADMK, 10 votes from DMDK, 5 votes from 4 other small parties/candidates, will total 50 votes. And these small adjustments are extremely difficult to detect and prove. * After the adjustments, these data could be uploaded to the corresponding EVMs automatically through an appropriate devices. * To give a familiar view of this process, its possible, to download all the data in an excel sheet along with EVM ID, adjust the values, and then upload these data back to the EVM, from this excel sheet itself. This is very much possible. Through automation, any number of EVMs could be manipulated in a short time. we have seen how the remote controlling of EVMâs can be done by a small group of 5 to 10 expert group. I cannot prove that this is what could have happened, but i am pointing out, that this is largely possible, with current technological advancement, no matter, what amount of safegaurds we have. Imagine, if atleast 25% of the EVMs are embedded with such wireless component, the result can be manipulated in atleast 25% of the constituencies. That comes around 136 constituencies of india, where the results can be adjusted remotely from anywhere in the world. THis is not a small number to ignore. cast your vote here: www.andhrasuperstar.com | ||
| One Hero Username: One Post Number: 10885 Registered: 09-2008 Posted From: 66.45.237.210 Rating: N/A |
While their point is valid, we can also consider the sivaganga constituency, where the result is changed at the last minute, but the news has been completely blocked //// same in RJY... | ||
| One Hero Username: One Post Number: 10884 Registered: 09-2008 Posted From: 66.45.237.210 Rating: N/A |
My personal experience of voting was like this â Went to the polling booth, presented my voter card, was told to get a slip, went and found a stall which was quite a distance from the polling booth, got a slip made, went back to the polling booth, presented my voter card, was referred to the next table and got my forefinger stained, went to the EVM, pushed the button. The machine beeped, but no light showed up so I walked out because other people were standing behind me. Later on I came to know that the light comes up 30 seconds after one has pushed the button. I am sure the EVMs were doctored. | ||
| Arjun1234 Junior Artist Username: Arjun1234 Post Number: 355 Registered: 09-2008 Posted From: 24.5.244.196 Rating: N/A |
http://psenthilraja.wordpress.com/2009/05/24/remote-controll ing-evm-manufacturing-election-result/ cast your vote here: www.andhrasuperstar.com |
